تمرین صبحگاهی Bare Metal Rust

قطب‌نما

(back to exercise)

#![no_main]
#![no_std]

extern crate panic_halt as _;

use core::fmt::Write;
use cortex_m_rt::entry;
use core::cmp::{max, min};
use embedded_hal::digital::InputPin;
use lsm303agr::{
    AccelMode, AccelOutputDataRate, Lsm303agr, MagMode, MagOutputDataRate,
};
use microbit::display::blocking::Display;
use microbit::hal::twim::Twim;
use microbit::hal::uarte::{Baudrate, Parity, Uarte};
use microbit::hal::{Delay, Timer};
use microbit::pac::twim0::frequency::FREQUENCY_A;
use microbit::Board;

const COMPASS_SCALE: i32 = 30000;
const ACCELEROMETER_SCALE: i32 = 700;

#[entry]
fn main() -> ! {
    let mut board = Board::take().unwrap();

    // Configure serial port.
    let mut serial = Uarte::new(
        board.UARTE0,
        board.uart.into(),
        Parity::EXCLUDED,
        Baudrate::BAUD115200,
    );

    // Use the system timer as a delay provider.
    let mut delay = Delay::new(board.SYST);

    // Set up the I2C controller and Inertial Measurement Unit.
    writeln!(serial, "راه اندازی IMU...").unwrap();
    let i2c = Twim::new(board.TWIM0, board.i2c_internal.into(), FREQUENCY_A::K100);
    let mut imu = Lsm303agr::new_with_i2c(i2c);
    imu.init().unwrap();
    imu.set_mag_mode_and_odr(
        &mut delay,
        MagMode::HighResolution,
        MagOutputDataRate::Hz50,
    )
    .unwrap();
    imu.set_accel_mode_and_odr(
        &mut delay,
        AccelMode::Normal,
        AccelOutputDataRate::Hz50,
    )
    .unwrap();
    let mut imu = imu.into_mag_continuous().ok().unwrap();

    // Set up display and timer.
    let mut timer = Timer::new(board.TIMER0);
    let mut display = Display::new(board.display_pins);

    let mut mode = Mode::Compass;
    let mut button_pressed = false;

    writeln!(serial, "آماده.").unwrap();

    loop {
        // Read compass data and log it to the serial port.
        while !(imu.mag_status().unwrap().xyz_new_data()
            && imu.accel_status().unwrap().xyz_new_data())
        {}
        let compass_reading = imu.magnetic_field().unwrap();
        let accelerometer_reading = imu.acceleration().unwrap();
        writeln!(
            serial,
            "{},{},{}\t{},{},{}",
            compass_reading.x_nt(),
            compass_reading.y_nt(),
            compass_reading.z_nt(),
            accelerometer_reading.x_mg(),
            accelerometer_reading.y_mg(),
            accelerometer_reading.z_mg(),
        )
        .unwrap();

        let mut image = [[0; 5]; 5];
        let (x, y) = match mode {
            Mode::Compass => (
                scale(-compass_reading.x_nt(), -COMPASS_SCALE, COMPASS_SCALE, 0, 4)
                    as usize,
                scale(compass_reading.y_nt(), -COMPASS_SCALE, COMPASS_SCALE, 0, 4)
                    as usize,
            ),
            Mode::Accelerometer => (
                scale(
                    accelerometer_reading.x_mg(),
                    -ACCELEROMETER_SCALE,
                    ACCELEROMETER_SCALE,
                    0,
                    4,
                ) as usize,
                scale(
                    -accelerometer_reading.y_mg(),
                    -ACCELEROMETER_SCALE,
                    ACCELEROMETER_SCALE,
                    0,
                    4,
                ) as usize,
            ),
        };
        image[y][x] = 255;
        display.show(&mut timer, image, 100);

        // If button A is pressed, switch to the next mode and briefly blink all LEDs
        // on.
        if board.buttons.button_a.is_low().unwrap() {
            if !button_pressed {
                mode = mode.next();
                display.show(&mut timer, [[255; 5]; 5], 200);
            }
            button_pressed = true;
        } else {
            button_pressed = false;
        }
    }
}

#[derive(Copy, Clone, Debug, Eq, PartialEq)]
enum Mode {
    Compass,
    Accelerometer,
}

impl Mode {
    fn next(self) -> Self {
        match self {
            Self::Compass => Self::Accelerometer,
            Self::Accelerometer => Self::Compass,
        }
    }
}

fn scale(value: i32, min_in: i32, max_in: i32, min_out: i32, max_out: i32) -> i32 {
    let range_in = max_in - min_in;
    let range_out = max_out - min_out;
    cap(min_out + range_out * (value - min_in) / range_in, min_out, max_out)
}

fn cap(value: i32, min_value: i32, max_value: i32) -> i32 {
    max(min_value, min(value, max_value))
}