嵌入式 Rust：进阶篇

RTC 驱动程序

(返回练习)

main.rs:

#![no_main]
#![no_std]

mod exceptions;
mod logger;
mod pl011;
mod pl031;

use crate::pl031::Rtc;
use arm_gic::gicv3::{IntId, Trigger};
use arm_gic::{irq_enable, wfi};
use chrono::{TimeZone, Utc};
use core::hint::spin_loop;
use crate::pl011::Uart;
use arm_gic::gicv3::GicV3;
use core::panic::PanicInfo;
use log::{error, info, trace, LevelFilter};
use smccc::psci::system_off;
use smccc::Hvc;

/// Base addresses of the GICv3.
const GICD_BASE_ADDRESS: *mut u64 = 0x800_0000 as _;
const GICR_BASE_ADDRESS: *mut u64 = 0x80A_0000 as _;

/// Base address of the primary PL011 UART.
const PL011_BASE_ADDRESS: *mut u32 = 0x900_0000 as _;

/// Base address of the PL031 RTC.
const PL031_BASE_ADDRESS: *mut u32 = 0x901_0000 as _;
/// The IRQ used by the PL031 RTC.
const PL031_IRQ: IntId = IntId::spi(2);

#[no_mangle]
extern "C" fn main(x0: u64, x1: u64, x2: u64, x3: u64) {
    // SAFETY: `PL011_BASE_ADDRESS` is the base address of a PL011 device, and
    // nothing else accesses that address range.
    let uart = unsafe { Uart::new(PL011_BASE_ADDRESS) };
    logger::init(uart, LevelFilter::Trace).unwrap();

    info!("main({:#x}, {:#x}, {:#x}, {:#x})", x0, x1, x2, x3);

    // SAFETY: `GICD_BASE_ADDRESS` and `GICR_BASE_ADDRESS` are the base
    // addresses of a GICv3 distributor and redistributor respectively, and
    // nothing else accesses those address ranges.
    let mut gic = unsafe { GicV3::new(GICD_BASE_ADDRESS, GICR_BASE_ADDRESS) };
    gic.setup();

    // SAFETY: `PL031_BASE_ADDRESS` is the base address of a PL031 device, and
    // nothing else accesses that address range.
    let mut rtc = unsafe { Rtc::new(PL031_BASE_ADDRESS) };
    let timestamp = rtc.read();
    let time = Utc.timestamp_opt(timestamp.into(), 0).unwrap();
    info!("RTC: {time}");

    GicV3::set_priority_mask(0xff);
    gic.set_interrupt_priority(PL031_IRQ, 0x80);
    gic.set_trigger(PL031_IRQ, Trigger::Level);
    irq_enable();
    gic.enable_interrupt(PL031_IRQ, true);

    // Wait for 3 seconds, without interrupts.
    let target = timestamp + 3;
    rtc.set_match(target);
    info!("Waiting for {}", Utc.timestamp_opt(target.into(), 0).unwrap());
    trace!(
        "matched={}, interrupt_pending={}",
        rtc.matched(),
        rtc.interrupt_pending()
    );
    while !rtc.matched() {
        spin_loop();
    }
    trace!(
        "matched={}, interrupt_pending={}",
        rtc.matched(),
        rtc.interrupt_pending()
    );
    info!("Finished waiting");

    // Wait another 3 seconds for an interrupt.
    let target = timestamp + 6;
    info!("Waiting for {}", Utc.timestamp_opt(target.into(), 0).unwrap());
    rtc.set_match(target);
    rtc.clear_interrupt();
    rtc.enable_interrupt(true);
    trace!(
        "matched={}, interrupt_pending={}",
        rtc.matched(),
        rtc.interrupt_pending()
    );
    while !rtc.interrupt_pending() {
        wfi();
    }
    trace!(
        "matched={}, interrupt_pending={}",
        rtc.matched(),
        rtc.interrupt_pending()
    );
    info!("Finished waiting");

    system_off::<Hvc>().unwrap();
}

#[panic_handler]
fn panic(info: &PanicInfo) -> ! {
    error!("{info}");
    system_off::<Hvc>().unwrap();
    loop {}
}

pl031.rs：

#![allow(unused)]
fn main() {
use core::ptr::{addr_of, addr_of_mut};

#[repr(C, align(4))]
struct Registers {
    /// Data register
    dr: u32,
    /// Match register
    mr: u32,
    /// Load register
    lr: u32,
    /// Control register
    cr: u8,
    _reserved0: [u8; 3],
    /// Interrupt Mask Set or Clear register
    imsc: u8,
    _reserved1: [u8; 3],
    /// Raw Interrupt Status
    ris: u8,
    _reserved2: [u8; 3],
    /// Masked Interrupt Status
    mis: u8,
    _reserved3: [u8; 3],
    /// Interrupt Clear Register
    icr: u8,
    _reserved4: [u8; 3],
}

/// Driver for a PL031 real-time clock.
#[derive(Debug)]
pub struct Rtc {
    registers: *mut Registers,
}

impl Rtc {
    /// Constructs a new instance of the RTC driver for a PL031 device at the
    /// given base address.
    ///
    /// # Safety
    ///
    /// The given base address must point to the MMIO control registers of a
    /// PL031 device, which must be mapped into the address space of the process
    /// as device memory and not have any other aliases.
    pub unsafe fn new(base_address: *mut u32) -> Self {
        Self { registers: base_address as *mut Registers }
    }

    /// Reads the current RTC value.
    pub fn read(&self) -> u32 {
        // SAFETY: We know that self.registers points to the control registers
        // of a PL031 device which is appropriately mapped.
        unsafe { addr_of!((*self.registers).dr).read_volatile() }
    }

    /// Writes a match value. When the RTC value matches this then an interrupt
    /// will be generated (if it is enabled).
    pub fn set_match(&mut self, value: u32) {
        // SAFETY: We know that self.registers points to the control registers
        // of a PL031 device which is appropriately mapped.
        unsafe { addr_of_mut!((*self.registers).mr).write_volatile(value) }
    }

    /// Returns whether the match register matches the RTC value, whether or not
    /// the interrupt is enabled.
    pub fn matched(&self) -> bool {
        // SAFETY: We know that self.registers points to the control registers
        // of a PL031 device which is appropriately mapped.
        let ris = unsafe { addr_of!((*self.registers).ris).read_volatile() };
        (ris & 0x01) != 0
    }

    /// Returns whether there is currently an interrupt pending.
    ///
    /// This should be true if and only if `matched` returns true and the
    /// interrupt is masked.
    pub fn interrupt_pending(&self) -> bool {
        // SAFETY: We know that self.registers points to the control registers
        // of a PL031 device which is appropriately mapped.
        let ris = unsafe { addr_of!((*self.registers).mis).read_volatile() };
        (ris & 0x01) != 0
    }

    /// Sets or clears the interrupt mask.
    ///
    /// When the mask is true the interrupt is enabled; when it is false the
    /// interrupt is disabled.
    pub fn enable_interrupt(&mut self, mask: bool) {
        let imsc = if mask { 0x01 } else { 0x00 };
        // SAFETY: We know that self.registers points to the control registers
        // of a PL031 device which is appropriately mapped.
        unsafe { addr_of_mut!((*self.registers).imsc).write_volatile(imsc) }
    }

    /// Clears a pending interrupt, if any.
    pub fn clear_interrupt(&mut self) {
        // SAFETY: We know that self.registers points to the control registers
        // of a PL031 device which is appropriately mapped.
        unsafe { addr_of_mut!((*self.registers).icr).write_volatile(0x01) }
    }
}

// SAFETY: `Rtc` just contains a pointer to device memory, which can be
// accessed from any context.
unsafe impl Send for Rtc {}
}